Air separation parts FAQ

Before the automatic valve is installed in the automatic valve box, it must be disassembled and washed clean, and the oil must be removed with clean alcohol. If it has been used, the automatic valve must grind the sealing surface, and then test the pressure with special tools. According to the manufacturing requirements, the leakage is less than 0.1L/min under the pressure of 0.6MPa. In actual work, kerosene leakage detection or soap water leakage detection can be used. Install the automatic valve in special tools first, put the pressure of 0.6MPa into it, and stop the pressure for 3 min. The standard of air leakage is: no more than 6 soap bubbles with a diameter of 40mm should be blown out within 3 minutes. The automatic valve that has passed the pressure test should be equipped with Open pin for standby. Special attention should be paid to the use of low temperature resistant brass or stainless steel products for the opening pin, and ordinary opening pin should not be used casuall...

Why does the air separation equipment require inflation before starting the water pump when starting the air cooling tower

What is dew point in air separation equipment and why can dew point be used to represent the moisture content in the air?

Before filling the molecular sieve, check that the sieve bed can not leak the molecular sieve, otherwise it should be handled. Oil and other sundries are not allowed in the tank; people who take part in the filling are not allowed to wear working shoes with nails in order to avoid stepping on the sieve bed; people should wear clean work clothes without oil. Several standard height marks should be made in the middle part, first check the ring chamber, and fill the aluminum glue to reach the standard height, then fill the molecular sieve. Due to the large amount of molecular sieves, the secondary output of molecular sieves in different kilns is generally different. Therefore, the molecular sieves of the same batch of kilns should be evenly filled with two molecular sieves. After the filling is completed, use the flattening mechanism to flattening first, and check whether the filling of the molecular sieve reaches the standard height (the molecular sieve has been buried below in the ri...

Core tips: answer: (l) the general requirements of reforming the high oil tank l) reforming the lubrication system of the centrifugal air compressor, the key equipment in the system of air separation plant. After transformation, centrifugal air compressor suddenly encountered emergency power outage, etc.

What is the difference between full heating of air separation equipment in the cold state and in the hot state, and what is the difference in the operation method?

Switching valve (forced Valve) is a pneumatic switching valve installed on the hot end of switching heat exchanger (or cooler. The switch of the switch valve is controlled by the signal compressed air through the solenoid valve. According to the different functions in the process, there are air, sewage and nitrogen switching valve, pure nitrogen suppression valve, sewage and nitrogen three-way valve, etc. It can be divided into vertical and horizontal structures. Vertical switch valve can be divided into air open type and Air closed type. Air open type means that when the signal compressed air is cut off, the valve flap can open automatically depending on its own weight; otherwise, it is gas closed type. The selection of gas on and off is determined by the safety of the device. Nitrogen switch valve uses air open type, air switch valve uses Air closed type. Since the movement of the switch valve is controlled by the solenoid valve, in addition to the choice of open gas and closed ga...

At the beginning of starting the full low pressure oxygen generator, all the air entering the equipment is inflated through the expander, while the total expansion volume of the expander (including the standby) set by the equipment is much smaller than that of the air compressor. In addition, at the beginning, the intake temperature of the expansion machine is much higher than the design value, and the actual air volume that can enter the expansion machine is less than the design expansion volume. Therefore, there must be a part of air to be emptied first, in order to avoid the air compressor overpressure or surge. When the liquid begins to accumulate, air is sent to the lower tower, then through the throttle throttle to the upper tower, and then combined with the expansion gas to the heat exchanger to recover the cooling. However, at the beginning, the air that can be eaten in the air separation tower is very small, because the liquid air, liquid nitrogen pipeline and regulating va...

What are the reasons for the factors affecting the operating cycle of air separation equipment

What is the cooling capacity in the air separation equipment project

There are many factors that affect the air displacement of centrifugal compressor. Except for the connection with design, manufacture and installation, the main factors that can affect the air displacement during the operation of compressor are: 1) the air filter is blocked or the resistance increases, cause the pressure of the compressor to reduce. When the outlet pressure remains unchanged, make the compressor pressure ratio increase. According to the performance curve of the compressor, when the pressure ratio increases, the exhaust volume will decrease; 2) the pipeline of the air separation plant is blocked, the resistance increases or the valve breaks down, which causes the exhaust pressure of the air compressor to increase. Under the condition of constant suction pressure, the pressure ratio increases, resulting in the reduction of exhaust volume; 3) the blocking or resistance of compressor intermediate cooler increases, resulting in the reduction of exhaust volume. However, t...

Vacuum pump is a device that produces, improves and maintains vacuum in a certain enclosed space by various methods. Vacuum pump can be defined as a device or equipment that uses mechanical, physical, chemical or physical chemical methods to pump the container to obtain vacuum. With the development of vacuum application, there have been many kinds of vacuum pumps, whose pumping speed has increased from a few liters per second to a few 100,000 liters per second, millions of liters per second. According to the working principle of vacuum pump, vacuum pump can be basically divided into two types, namely gas transmission pump and gas capture pump. As the requirements of vacuum application technology in the field of production and scientific research for its application pressure range become wider and wider, most of them need to be made up of several kinds of vacuum pumps. The vacuum pumping system can only meet the requirements of the process of production and scientific research after ...