当前位置: Home / Faq / Large air separation FAQ /

Why should the air separation tower be blown away and how should it be blown away correctly?

Why should the air separation tower be blown away and how should it be blown away correctly?
Oct 12, 2022
Author: DEAR AST
Question Reply

Blowing off is the operation of removing solid impurities and free water by the impact of airflow, and at the same time, it can also expel part of the heat and cold energy stored in the equipment. After installation and overhaulAir separation equipmentIt is easy to remain solid impurities and water drops, so it should be blown away; when the device is stopped, the cooling capacity of expelling part should be blown away, and after the heating operation, it should also be blown away to expel part of heat and further clear away water.
There are roughly two blowing methods: continuous blowing and intermittent blowing. The so-called "continuous blowing-off" is the blowing-off method that always opens the blowing-off valve and lasts for a period of time. The so-called "Intermittent blow-off" means that the blow-off valve is closed and open at the same time. When it is closed, it is opened suddenly after holding high pressure, and it is repeated. This method has better effect on removing solid impurities and free water. Because the pressure difference increases when the pressure is suffocated, the airflow speed increases when the blow-off valve is opened, and the impact clamping effect strengthens.
If the drying gas is not used in the blowing-off process, the water in the cold equipment will reach saturation, and the water may be precipitated in the equipment, and even the water will freeze and freeze the pipeline and equipment. Moreover, after blowing off, the remaining wet gas in the equipment is easy to elude water drops when the temperature changes. To reach the purpose of equipment drying, it is best to use dry airflow to blow off. For cold equipment, when the temperature does not rise to above 0℃, do not blow off with wet air.
The blowing-off procedure is to clean the pipes outside the tower first to prevent the impurity from entering the tower; in the tower, first blow the air heat exchanger, and then blow off the tower, finally, blow the tower and liquid oxygen and liquid nitrogen emission system.

DEAR Air Separation Solve YourWhy should the air separation tower be blown away and how should it be blown away correctly?You can also learn about otherLarge air separation FAQ about DEAR Air Separation, and solve the problem for you.
Didn’t find the problem encountered?
Please contact live chat or email for quick help.
Related FAQ
More Related FAQ
The comprehensive energy-saving transformation of cryogenic air separation is not a single point of equipment replacement, but a collaborative optimization of the whole system, which mainly covers six technical sectors: 1. optimization of compressed air supply system: frequency conversion/permanent magnet transformation of air compressor, matching of air supply pressure, reducing the loss of venting and depressurization, solving the problem of "big horse pulling small car", and the compression link accounts for more than 70% of the total energy consumption of air separation, which is the focus of energy conservation; 2. transformation of precooling and purification system: high efficiency and low resistance molecular sieve, adaptive regeneration control, air inlet precooling, reduce regeneration energy consumption and system resistance, and reduce compressor load; 3. upgrading of rectification and main heat exchange system: efficient and regular packing, optimization of reflux ratio, o
2026.11.20
Answer:>>the conventional air separation unit of DEAR air separation plant is designed for 20 years, which meets the design service life recommended by national standards and specifications, and is also the cost-effective optimization scheme for bot/boo gas investment and long-term stable gas consumption projects. The default recommended design service life of the national standard and relevant specifications, feasibility study, bidding and preliminary design drawings of pressure vessels is 20 years. Designed for 20 years: the cold box plate, heat exchanger and pressure bearing parts are of higher material selection grade, suitable for long-term continuous operation, and suitable for bot/boo gas investment, metallurgy and chemical industry long-term gas supply projects; The maintenance is in place and the technical transformation is timely. The actual stable service can reach 20-25 years, and the working condition management can reach 28-30 years. 15 years of design: moderate investmen
2026.11.20
Need more information?
Contact us for more details about our air separation equipment, solutions and services.
Products
  • Large air separation
  • Small air separation
  • High purity nitrogen air separation
  • Liquefaction air separation
  • Complete air separation
  • Biogas purification
  • Air separation parts
Need more information?
Tel:+86-19837850537
© Kaifeng DEAR Air Separation Industry Co., Ltd.. All rights reserved.
Online
Inquiry
Email
Top