What types of water cooling tower are there?

Nov 09, 2023

Author: DEAR AST

Question Reply

Water cooling towerIt is a hybrid heat exchanger. The purpose is to lower the temperature of cooling water in the cooling tower after cooling the air, so that the air cooling tower can be recycled. Different types strive to enhance heat transfer, improve cooling effect, and at the same time, flow resistance should be as small as possible, so that water is not easy to scale.
Large scale in ChinaAir separation equipmentThe structure of water cooling tower selected is roughly in the following types:

1) stuffing tower. In the early stage, it was a Laci ring with porcelain. Its heat transfer effect was good and the resistance was not big. However, when it is used in the process of self-clearing low pressure, because the switching system is switched once every few minutes, when the switching is emptied, the impact of airflow on the porcelain ring is relatively large, which is easy to cause the damage of the porcelain ring and increase the resistance. Some are also changed into plastic rings to increase the strength. Currently at 6000 ~ 40000m³A new type of stuffing tower is used on the air separation plant of/h, which adopts Alpha ball ring or common ring and ladder ring. It has the advantages of large flux, small resistance, good heat transfer effect and good strength. The temperature difference of heat transfer at the hot end is about 0.5 ℃, and the negative temperature difference of effluent (the temperature of water is lower than that of nitrogen) can reach 4 ~ 9 ℃, depending on the gas-liquid ratio.

2) swirling plate. It is composed of several metal structure swirling Tower plates. This kind of structural resistance is very small and will not be damaged. It has been used as an improved type for quite a long time. But the heat transfer effect than packed tower.

3) sieve tower. The tower plate adopts drench Tower plate with larger aperture and hole spacing. Both nitrogen and water pass through the sieve hole. Since the water cooling tower does not work continuously and stably, the cooling effect is not ideal enough, so it is no longer used now.

Why does the air separation equipment pre cool the main cooling system before liquid accumulation and rely on liquid air evaporation to cool the main cooling system differently

What types of DEAR Biogas purification unit water cooling towers are available?

DEAR Air Separation Solve YourWhat types of water cooling tower are there?You can also learn about otherSmall air separation FAQ about DEAR Air Separation, and solve the problem for you.

Didn’t find the problem encountered?
Please contact live chat or email for quick help.

Chat online service@dearast.com

Related FAQ

More Related FAQ

I want to make a small cryogenic air separation unit with argon. What manufacturers' technology is relatively mature, and what are the key points of model selection?

Answer: select the small cryogenic air separation unit with argon, and give priority to verifying the real continuous operation performance of the unit with argon below 1000nm ³/h, avoiding the scheme with only drawings and no long-term operation record. Key dimensions of model selection: 1. operation performance: it is confirmed that the manufacturer has a long-term stable production case of small flow air separation with argon. Deere air separation small-scale hydrogen free total distillation argon extraction air separation, supports scale customization below 1000nm ³/h, and is equipped with intelligent control system, with mature landing performance. 2. power consumption per unit liquid argon

2026.11.06

How much can the pressure of air compressor be reduced for energy-saving air separation equipment?

Answer: the default unit gauge pressure is MPa (g), and the mainstream is cryogenic full low pressure external compression process. Design pressure of conventional energy-saving models in the industry: 0.50~0.55 MPa (g); The lower limit of stability of ordinary process is about 0.45 MPa (g). In general, it is not recommended to be lower than 0.42 MPa (g) for a long time in the conventional scheme. If the pressure is too low, there will be risks such as poor heat exchange in the precooling tower, insufficient purification of molecular sieve, difficult to balance the cooling capacity, and the air compressor close to the surge area. The internal compressed air is distributed with a booster. The main air compressor is mostly 0.55~0.65 MPa (g), and the lower limit is mostly 0.50 MPa (g), which is difficult to achieve below 0.45MPa (g). Deere air separation ultra-low discharge pressure patented energy-saving external compression air separation, through the collaborative optimization of the w

2026.11.06

Related Products

More Related Products