当前位置: Home / Faq / Liquefied air separation FAQ /

What should be paid attention to after using molecular sieve to purify air?

What should be paid attention to after using molecular sieve to purify air?
Aug 04, 2023
Author: DEAR AST

1) A little bit more work pressure is needed. The pressure depends on whether to use the original dryer valve or switch to the large diameter valve when switching to the molecular sieve purifier; whether to use the original dryer pipeline or to thicken the pipeline. If the valve is larger and the pipe is thicker, the increase of working pressure is smaller. If the valves and pipes of the original dryer are used, the pressure of the upper column will increase by about 0.01 MPa, and the pressure of the lower column will increase accordingly. Otherwise, the regeneration temperature of Molecular Sieve Purifier will not meet the requirements within the predetermined time.

 

2) The regeneration temperature of molecular sieve purifier must be strictly controlled. The temperature of heated nitrogen from the heating furnace should not be too high or too low, usually controlled at 280-320 ℃. If the temperature is too high, the furnace is prone to failure; if the temperature is too low, the heating regeneration cycle will be extended. When the temperature rises to 110 ° C, the nitrogen is heated out of the purifier to stop heating. After the power supply of the electric furnace is cut off, the temperature of the heated nitrogen from the purifier may also rise to more than 130 ° C.

 

3) When the molecular sieve purifier is switched over, air should be filled from above. Although the molecular sieve is full at the initial loading, there will be a gap in the upper part after vibration. If air is filled from below during the switching process, the molecular sieve will jump up and down, causing friction and crushing.

 

4) The molecular sieve purifier should be switched slowly to avoid the fluctuation of working conditions of fractionator or the powder produced due to the influence of gas flow on molecular sieve. When there is an argon column, the molecular sieve purifier needs to be switched stably.

 

5) When shutting down for a long time, nitrogen should be filled to prevent moisture. During long-term shutdown, it is best to fill the purifier with dry nitrogen to maintain pressure. In order to prevent moist air from invading the molecular sieve, the ability of purifying air will be reduced when the molecular sieve is driven again.

DEAR Air Separation Solve YourWhat should be paid attention to after using molecular sieve to purify air?You can also learn about otherLiquefied air separation FAQ about DEAR Air Separation, and solve the problem for you.
Didn’t find the problem encountered?
Please contact live chat or email for quick help.
Related FAQ
More Related FAQ
The comprehensive energy-saving transformation of cryogenic air separation is not a single point of equipment replacement, but a collaborative optimization of the whole system, which mainly covers six technical sectors: 1. optimization of compressed air supply system: frequency conversion/permanent magnet transformation of air compressor, matching of air supply pressure, reducing the loss of venting and depressurization, solving the problem of "big horse pulling small car", and the compression link accounts for more than 70% of the total energy consumption of air separation, which is the focus of energy conservation; 2. transformation of precooling and purification system: high efficiency and low resistance molecular sieve, adaptive regeneration control, air inlet precooling, reduce regeneration energy consumption and system resistance, and reduce compressor load; 3. upgrading of rectification and main heat exchange system: efficient and regular packing, optimization of reflux ratio, o
2026.11.20
Answer:>>the conventional air separation unit of DEAR air separation plant is designed for 20 years, which meets the design service life recommended by national standards and specifications, and is also the cost-effective optimization scheme for bot/boo gas investment and long-term stable gas consumption projects. The default recommended design service life of the national standard and relevant specifications, feasibility study, bidding and preliminary design drawings of pressure vessels is 20 years. Designed for 20 years: the cold box plate, heat exchanger and pressure bearing parts are of higher material selection grade, suitable for long-term continuous operation, and suitable for bot/boo gas investment, metallurgy and chemical industry long-term gas supply projects; The maintenance is in place and the technical transformation is timely. The actual stable service can reach 20-25 years, and the working condition management can reach 28-30 years. 15 years of design: moderate investmen
2026.11.20
Need more information?
Contact us for more details about our air separation equipment, solutions and services.
Products
  • Large air separation
  • Small air separation
  • High purity nitrogen air separation
  • Liquefaction air separation
  • Complete air separation
  • Biogas purification
  • Air separation parts
Need more information?
Tel:+86-19837850537
© Kaifeng DEAR Air Separation Industry Co., Ltd.. All rights reserved.
Online
Inquiry
Email
Top